Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I've the following situation:
1. Send CoAP message trough send(), this causes the the nRF9160 to start RCC connection
2. Wait for RCC connected mode (LTE_LC_RRC_MODE_CONNECTED...
Hello!
I am in the process of adding OTA DFU support to our existing application. However, I'm having problems starting the DFU process.
For security reasons we want to...
Hi there,
We are using the nrf9160 DK with Serial LTE Modem (1.8.0) to run some tests on the modem (1.3.1). We are using the MQTT client AT commands in order to connect...
Good day
I am attempting to use lwm2m to post temperature sensor data. At the moment I'm trying to to initialize object with ID 3300 (generic sensor)but it is not appearing...
MacOSX 13.0.1, Intel. nRF Connect SDK v2.2.0 as downloaded by Toolchain Manager v1.2.1 from nRF Connect for Desktop 3.12.1.
Same happened with SDK v2.1.2.
Similar steps...
Hi,
I was trying to put the nRF5340 Audio DK board in DTM mode to test RF capability but couldn't find out any way to do so.
Please let me know if I can find some documentation...
Hi,
We have 3 nrf5340 Audio DKs we want to connect together. One of the devices is connected as central and the two others are connected as peripheal. By know, the two peripheal...
Hi!
We plan to build an AoA localization system with the nRF52833. To calculate the signal phases per channel, the antennas are connected to the BLE-RX via switches sequentially...
I am working on the nfc uart examples. first I found the poller example is not support for 10056 board. I make the change for that. code can build and flashed, but then I...
Hello,
My development requires new device binding and I want to share the steps followed and my issue.
My device is Renesas and commuicate via I2C protocol.
Based on...
Hi Team,
I am using nrf52840 controller and SDK 16.0. I have referred to the product specification manual/data sheet already. However, I would like to have the " programmer...
Hi,
We received the new nRF52840 USB dongles this week, however when we try to access the getting started URL on the dongle package the web page gives an error.
The...
Hi
I am creating a simple firmware based on BLE Peripheral UART for nrf5340 (currently using DK). Before, I able to create notification to user app (I am currently using...
Hi,
I get some question about the nrf52833 nfc digital modulation signal feature. I think the biggest changes is allow to using external frontend. I just want to check if...
I use VSCode as my primary development environment for several different client project. I recently have been evaluating the nRF Connect extension for VSCOde. I do not want...
