Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Is there a way to initialise a GPIO earlier than in main() without modifying NCS/zephyr code?
We tried an PRE_KERNEL_1 init() function, but this is rather late still.
...
I have two central devices and two peripheral devices each paired with two different services.
I wish each pair can connect only to each other and don't mix up the connection...
Hello,
I am trying to set up for Receiver blocking test for a product that uses both BLE and 802.15.4. The HW is an nRF52840 along with an nRF21540 FEM. I have a couple...
Hi guys,
As I want to debug on my nRF52840 Dongle with a Debugger, my first step was to connect it with internal segger OB JLINK integrated into nRF52840DK. This was not...
Hi,
I've been using the SDK shipped with a vendor product and a feature that I use is to acquire the SPIS semaphore as part of the SPIS handler. The version of the SDK that...
Hello Nordic team,
I'm a beginner on Nordic connect sdk, here have a question about how to increase nrf5340 sending data speed by NUS?
Below is what I testing model now...
Hello.I will open it again because the ticket was closed due to my fault. I want to check the LE Audio (CIS/BIS) function by capturing it as "Airlog" or "hcisnoop" with nRF5340...
Hello,
I am currently working on a project where I need to receive data from a custom board using a nRF52833.
I have made custom characteristics and I can send commands...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
I am new to pcb design so forgive my questions:
I see the reference circuitry for the nrf52840 and some PCB guidance around the nfc antenna design, but I haven’t found...
nRF52832 & SDK 15.3.0
I have the opposite problem to the one described in https://devzone.nordicsemi.com/f/nordic-q-a/60117/relationship-between-ble_stack_init-and-current...
hi I using nrf53832 and I used the your SW Bootloader from the SDK
we burning the application using BLE communication in your SW I see abort message NRF_DFU_OP_ABORT
I...
I've been piecing examples together and I think I'm getting close. I'm using the NRF52 DK PCB.
I can get the RTC to trigger callbacks but it seems to be running way too...
Hello, I'm an android developer.
I stuck at this problem while I was doing my job.
My task is to put BLE DFU function into our app.
To achieve this, I have put...
