Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I have troble when try to change custom service to Environment Sensing Service in this sample
https://github.com/maidenone/custom_ble_service_example
I used the sample...
Cheers!
I've been working to enable TWI0 for our current project, but I've been getting stuck on this compile error:
../SDK/modules/nrfx/drivers/include/nrfx_twi.h:73...
Hi i tested the code with nrf52DK with same code getting 3 analog value from AIN1, AIN2, AIN3 and it worked fine.
But when I use EYSHSNZWZ for my pcb, ADC value was just...
Hi,
On battery powered devices, how is it possible to retain a root key when changing batteries?
The crypto cell has an Always On power domain for retaining device secrets...
Hi guys,
I'm currently using SDK 15.0.0 in Keil MDK and making use of the new NRFX drivers.
Similar to the issue detailed here: https://devzone.nordicsemi.com/f/nordic...
Hi,
In the documentation , you have specified that the nRF Toolbox is supported for mcumgr FOTA.
However, from our tests, it seems that it is not true. Could you please...
Hi,
I'm experimenting with the lwm2m sample on the nRF9160-DK and I enabled the firmware update pull support through a COAP to HTTP proxy :
then simply added :
and the...
Hello peer developers,
This is a general question and dilemma I am dealing with and I wanted to get your opinion.
I am working on a project to implement a short range...
Hi,
Here, i have using two I2C functions EEPROM + SENSOR with nRF52832.
Initially, using ble_app_uart example to read Sensor data using TWIM.
Every minute read Sensor...
I started with ncs/nrf/samples/nrf9160/lte_ble_gateway and have taken parts of ncs/zephyr/samples/subsys/fs/fat_fs to get SD card support
prj.conf
CONFIG_NEWLIB_LIBC...
Here are some of the issues which I am facing in SEGGER Embedded Studio since I updated to nRF Connect SDK v1.3.0:
After I press Debug, Go, a dialogue box opens asking...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
The serial_lte_modem sample is heavily broken. Unlike the AT client sample which simply works with PuTTY out of the box, for the serial_lte_modem you need to configure PuTTY...
Hi all:
I am using sdk 16.0.When put system on idle mode call two times sd_app_evt_wait it works well.But I want to save power,so before enter idle mode,but when I call...
Hi despite trying 3 different approaches (even using the Nordic driver lis2dh12 on a blinky-based project and installing Segger Studio to step/debug into the library code...
