I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
So I was following the documentation. Installed everything successfully. And now I am trying to send the program to the nrf52840. However when I do ninja flash<program> I...
I've been trying to create a simple SPI to UART bridge starting with the peripheral template example from the nRF5 SDK 16. I want to read 5 bytes from uart, send them via...
I've reviewed the different PWM examples that include the low power PWM, PWM driver and the PWM library. What I'm looking for is a very simple solution to drive a bipolar...
Hi,
I'm wondering if the current nRF sniffer firmware (v3.0.0) can detect extended advertisements on arbitrary channels? Is it supported in the firmware? If so, can I use...
Hi all,
I did not do mesh SDK for a long time. Now when I see SDK Mesh, I saw Low power Node example. It can run with Mesh network and update OTA by DFU buttonless (I don...
Hi,
I had an experience with embedded programming but never with wireless technology. I am using Nordic SDK v16.0.0 and nRF Mesh SDK v4.0.0.
Here is a short description...
Hello All,
I am working on the Nrf52810 board with sdk 14.2.
I have implemented the read ,write , delete feature in my code.
Now it is creating new entry for repeating...
Dear All, I am trying to compile an application based on the Zephyr project for the nrf52. I am following the instructions from here .
I am using Windows. Using SES everything...
Thanks in advance.
Hi guys am working with nrf5282 (softdevice s132 V1.6.0 and SDK version 15.2.0), also enabled freertos, and also make softdevice changes rleated freertos...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
As part of my Factory setup we want to download MBR, bootloader, SoftDevice...
Hi,
I would like to perform DFU over Mesh. I am following the steps
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v4.0.0/md_doc_libraries_dfu_dfu_quick_start...
Hi,
anyone help me.
I am facing the issue during DFU with OTA. the steps are listed which had I done,
here trying to update softdevice.
1. Erase all.
2.flashed softdevice...
hey guys,
I want to write a c code to display temperature sensor data which is inbuilt in the nrf52840. I am using segger embedded studio. Can I get some reference code...