An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
Hi,
I am trying to run the ble_app_uart_coexist example on my nRF52840 Development board.
I followed the above steps for configuring the example to work.
I copied...
how to include SPI Master code in ble_app_uart sample code of pca 10028(nRF51822) board. its soft device is sdk 10.0.0 (s110). Please share me a sample code if you have. ...
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
