I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
want to try out the nRF52x Family, so will buy the DK board, which IDE is recommended? I am familar with VS Studio or Atmel Studio 7, so is there something like that...
Hi:
I want to capture the parameter of a digital wave like this, I want to get every 't' value. The wave is same in a period of time, but the 51822 capture value of 't' is...
SDK: 10.0.0
Softdevice: s110_nrf51_8.0.0
I'm working on migrating our application from SDK v9 to v10. I'm getting a softdevice assertion failure in src/rem.c line 1371...
Hi,
Can I use power profiler kit for current measurement of nRF52840 SoC?
If yes is there any hardware and software revision version(s) for power profiler kit?
Please...
I created a BLE Peripheral to read the light intensity, the purpose is connected to the iPhone device to read the update value in the BLE_NRF_52 device.
For the calibration...
Hi,
I checked this thread https://devzone.nordicsemi.com/f/nordic-q-a/24611/how-to-change-the-name-of-bootloader-s-dfutarg which suggests to modify the macro but I would...
Hello
for my project at the university I have to implement a bluetooth mesh network using 4 nordic thingys:52 and one nRF52DK(only for programming purposes, not part of...
Hi All!
I use Example Project from SDK: "examples\peripheral\usbd\" as reference to implement my HID device simple protocol (EP1IN / EP1OUT 64bytes)
The Question is how...
I am working with the BL652 Module from Laird, and with Keil 5, using a ST Link SWD programmer clone.
I am using the ble_app_uart_timer_driven_scan_mode from the ADC examples...
Hi, I am developing an IoT sensor (peripheral device) using SDK v11.
On my sensor, I have defined an advertising packet that broadcasts the complete local name and a scan...
I'm in the process of porting my application from SoftDevice S132 v4.0.2 / SDK v13.0.0 to SoftDevice S132 v6.0.0 / SDK v15.0.0. I noticed that the define for BLE_GAP_TIMEOUT_SRC_ADVERTISING...
Hello,
I'm attempting to use a high-limit reached event from the SAADC to trigger the clearing of a GPIO. My wish is to disable this GPIO with the lowest possible latency...
I used SDK 13.x to create a custom profile with services for nRF52832 with BLE 4.2
If I go to a nrf52840 with BLE 5.x SDK, can I use the exact same code, or do I have to...
