Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am using SDK 15.2 with IAR's EWARM 8.30.1 and the nRF52840 Development Kit. My eventual target is the nRF52-Dongle. If it matters my development OS is Windows 7 64-bit....
I would like to write code to disconnect from any connected device. My system is a ble peripheral with s132 6.0.0.
My code calls:
result=sd_ble_gap_disconnect(BLE_CONN_HANDLE_ALL...
I starting working with examples for the nRF9160. Zyphr seems like a very complicated OS (like Linux with device trees, etc) and difficult to use with a debugger.
Is the...
Hi,
I trying to convert a stm32 function code to nRF52. The goal is to use a spi periperal on my custom board.
In this application we need to have 2 bytes transfert. That...
I can communicate with success from the pc to my custom nrf52832 device (SDK 15.2, S132v6.1) using the pc-ble-driver (sd_api_v3) with Tag 4.0.0 from Github. Great work!
...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
Hello,
I'm currently using an nRF9160 DK v.0.7.0 and the provided samples like the asset tracker and the at command client. Compiling, flashing etc. of the firmware already...
