Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
My environment: DK 10040, nRF52832, SD 6.1.1, SDK 15.2, SES 3.52
When does the SAADC use power? And when does it stop using power?
I searched the 52832 specification and...
I am trying to run the example from this page: www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
I have PCA100040 somehow after running blinky and others...
I am trying to get a driver from a third party binary to work. Their library was compiled without using the HW FPU. I had to compile my code to use the softfp. I also added...
I posted on the Adafruit forum but there doesn't seem to be much support there. Since the module is based on nrF I'm hoping this community can help out.
For the most part...
hi,
i am using nrf51422 ble_app_uart(sdk 12.3.0) example
i am receiving a string through app_uart_get() function, i want to compare it then i have to send some predefined...
SDK15, s132 6.0, nRF52832
Hi!
I need to know before connect on the central side (from advertise data), that this piripherial device has already bonded.
Is it possible...
I'm having some trouble setting up 2 transports (BLE + USB CDC ACM) with the secure_bootloader example. The changes I made were:
- Increased flash size for code space in...
Hi,
It's my first design with nRF52840 (I have make multiple design with nRF51 et nRF52 without problem).
I use SDK15.2 and BLE_peripheral_blinky example without modification...
I'm using nrfjprog to develop a production functional tester for an nRF52840 based system. Everything was going well in testing, but when I moved the hex file to be loaded...
Hello
I have a problem with ADC measure and accuracy.
I want to read a voltage (U_BAT+) between 2.5 – 4.5V with an accuracy of < +/- 50mV
I have two scenarios. ...
Hi. I want to output numbers to tm1637 display with nrf52832. The existing library is dedicated to Arudino, so we will contact you to change it for nRF52. (Existing library...
Hi,
I am having some task which for which i am using GPIOTE, PPI & TIMERS together to achieve and in SDK 14.2, the over all power consumption of my board is 10u which...
I am trying to integrate DFU into ble_app_uart example.
I am using nrf51422 board, sdk v10.0.0, soft device "s110_nrf51_8.0.0_softdevice.hex".
I have made some changes...
I'm trying to use Pin 0.21 as SCLK in the SDK15.2/examples/peripheral/spi/pca10056/blank/ses.
The example works fine with CLK on pin 3 (default) and on pin 29 (just tried...
Hi,
I created nrf52 project on Segger studio. I'm writing directly registers.(not SDK)
It includes i2c,uart and adc, this part is working now.
I want to add SoftDevice...
