Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I use the nRF52832 IC of WLCSP package.
In addition, it sets as follows:
{.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16, \
.rc_temp_ctiv = 2, \
.xtal_accuracy...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
We have noticed that when our application is trying to call GATT disconnect while nRF master app is running, our app fails to disconnect. More over, when our app connects...
Hello everybody,
I am trying to pair module nRF51822 with Heart Rate Monitor device with the Surface Pro running on Windows 10 with no success. I see the module but when...
This question is a follow-up to this post . After performing several tests and understanding that some phone are more limited than others in terms of the number of exchanged...
Hi,
my device resets on executing sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler);
I have external 32KHZ crystal. I also know that software works because...
Hi all,
I have a quesion about reading a value's characteristic in the Android app nrf Master control panel.
I read a value, and i have the good value but i have a letter...
What happens if I call app_timer_start() to start a repeated timer. And at the same time I do a pstorage_clear() and pstorage_store()? Will the timer events get halted during...
I'm using the softdevice S310 on nRF51422 and when the softdevice is enable and I erase flash, the device won't go to sleep.
My code implementation is like as below:
...
There is a way to set the initial value of a characteristic. But how do I set the value after this without sending a notify to the master? Is it possible to write the value...
Hello,
i want use the port event to trigger timer 1. I need only one interrupt source and i don't want to use the pin event because of the higher current consumption. Its...
