Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
HI.
NRF connect For Desktop Programmer program Fail.
So I used command Tool (nrfjprog). command Tool worked.
Enviroment:
- nRF Connect For Destop v5.1.0
- Programmer...
We're attempting to provision one of our nRF9160-based IoT devices to our AWS VPC.
We're following this procedure:
Provisioning our eDude on AWS
Step 1: Provision the...
I'm trying to get FOTA updates working on the NRF54L15 DK. I noticed there isn't a dedicated guide available for these yet so have been using this page: https://docs.nordicsemi...
I’m encountering a build issue with Zephyr (version 3.7.99) on my custom board based on the nRF52840 SoC. The build process fails during the linking stage with an undefined...
Hi ,
We are using MCU nRF52832-QFAA-R (Flash 512KB & RAM 64KB) with softdevice s132 - 6.0.0.
I am not sure what is extracly Soc Revision of the MCU ? But I read some information...
I have a custom SMP handler that uses an SPI transport. If I use the pin reset to reset the module after programming sometimes the module hangs when calling that handler....
Hi We would like to use the nRF5340 with a custom network core image that runs the full Bluetooth stack and I have gotten it to work with sysbuild. However, we would like...
