Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
How should the addressing be between an nrf24LU1+(transmitter) and nrf24l01+(Reciever) in the code.?
The registers TX_ADDR, RX_ADDR_P0, RX_ADDR_P1 are updated on a device...
Do we need to explicitly set the ENABLE field (Bit31) of RADIO->OVERRIDE4 when applying the override values from FICR->BLE_1MBIT[n]?
From the few samples I've checked,...
Please teach me the minimum theoretical value of the transmission time in the following conditions.
CPU --> nRF24L01 --(2.4GHz/1Mbps)--> nRF24L01 --> CPU
CPU -->...
I need to send a long (let's say 10Kb) notification from Bluez 5.37 on my Linux device to a mobile phone.
My implementation is based on src/shared/gatt-server.c .
I...
Hi,
I have put in my chip (nrf51422):
-1 softDevice s110 8.0.0;
-2 application (hrm_whit_dfu);
My problem is:
when i send characteristic to start advertising the board...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
