Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello,
It seems there is an issue in measure voltage process of ST25R3911 Lib.
Measure voltage function use POWER_SUPP_MEAS_FRACTION_DIVISOR = 100. But it seems that POWER_SUPP_MEAS_FRACTION_DIVISOR...
I saw this issue brought up 3 years ago, but I think the conditions are changed now since that was on NCS 1.
I am trying to do bt_hids_inp_rep_send about 10 times per connection...
Hi folks
We are facing an issue with occasionally ~240 uA added current consumption on our nRF52832 based custom board when it comes out of reset. We only see the problem...
Hi all,
currently, I'm using NCS 2.4.0 with nRF9160 board (custom board).
I'm facing issue once enabling CONFIG_TFM_PROFILE_TYPE_NOT_SET.
The issue is bootloader won...
I'm working with nRF Connect SDK (Zephyr). In that I am using 255 byte array to get response from nrf52832 through BLE. my code is getting crash in response back. when I decrease...
Using the nRF52840 with NCS v2.6.1, I want to put the device into a low-power sleep state during idle time. Before sleeping, I configured a GPIO interrupt as the wake-up source...
Hi everyone. I'm trying to read data from an MS5611 pressure sensor using the nRF52840,
but the I2C communication isn't working.
Upon checking, I noticed that the I2C...
I have a board with an nRF9151 device on it that was provisioned to the nRF Cloud under one User Account.
I would like that device to be in a different User Account, and...
Hi,
I'm using nRF connect extension with VSCode and developing for Actinius Icarus IoT board (which uses nRF9160).
Even when building the example code of hello_world ...
I tried generating sec_tag using sys_rand32_get() or other arithmetic method during runtime. All 3 certificates (CA, client cert, client key) were able to be written into...
I want to compile the ble_uart example using Segger Embedded Studio. I installed today the latest version V8.16. I am using nRF5_SDK_12.3.0_d7731ad.
I imported the project...
Hello,
I'm trying to change the name of the USB port in the "usbd_ble_uart_freertos" example code. Currently, it shows up in the Device Manager as "USB Serial Device (COM12...
I am developing a simple BLE mouse using ble_app_hids_mouse of SDK17.1.0. I found out through devzone that left mouse button click sends (1, 0, 0) and right button click sends...
I'm unable to load values into characteristics—they show up as N/A on the nRF Connect app. I tried to enable notifications using the Client Characteristic Configuration, but...
Hi Nordic Community I have a problem with the PAwR examples were I'm unable to place a sync interval bigger than 2 secs.
The example starts with an interval of 0xFF * 1...
