Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I am trying to run the blinky Demo on the nRF52DK on VScode, the whole process is smoothly, but it can't work, the LED no any action. could you know anything I miss? many...
When I was making the upgrade package, I encountered a problem, and there was no problem in making only one upgrade package.
It is also possible to make protocol stacks...
Hi All,
Using VS code, nr52840dk,v2.6.0sdk，sid_end_device demo, No changes have been made
Firstly, add build config
Then click on Flash
Clicking VCOM0 has no logs...
Hello, I'm using the example "smp_client_ble," and I can't manage to remove the boot message.
Below is my .prj file:
My toolchain is: NRF Connect SDK V2.2.0
I am...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
We recently purchased the module 453-00052R from Digi-Key and have successfully implemented it into our project. The design is complete, and we are now attempting to flash...
Hi,
I am trying Asset Tracker V2 application in my custom board and rechecking results with DK to ensure no hardware reasons are there. Using SIM supplied with DK and...
Hi Support Team
Our project need 8mA charge current, how to configure charge current of nPM1300 to 8mA？ Or could you provides us other nPM chip or solution that can meet...
Hi all,
I have a custom board running on nrf9161. I need to flash the custom board with the NRF9160-DK. But I am running into some issues. the development is at early stages...
Hi,
I'm trying to add a manufacturing specific attribute to the On/Off cluster.
To do this I have so far created a custom attribute list with ZB_ZCL_DECLARE_ON_OFF_ATTRIB_LIST_CUSTOM...
Hi NordicTeam
i am working with the Mesh Dimming server example out of the SDK MESH 5.0.0.
While investigation the Packet loss in my prevous ticket i was wondering if...
Hi,
Working with the NRF5340-nrf7002 and the W25Q16RV flash memory in our project.
Initially, I configured an 8MB( W25Q64RV) external flash without issues and tested...
I've been testing the FMDN locator tag sample application with a nRF52840 devkit and I would very much like to get an answer to the following questions:
1. Is it possible...
Hi, I'm having an issue with the bt_mesh_resume() function in my project based on Zephyr and Bluetooth Mesh. My code is trying to cycle the Mesh network on and off to save...
