Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Dear Nordic Experts,
Is there any way to detect the the WDT has reset the system. I mean some WDT register from which you could read this information, and that would be...
Hi,
I use nrf5340 with nrf connect SDK 1.9.1
I found some issue when: 1. My peripheral device that running connected and paired to some Central device.
2. The central...
Hi guys. I was observing the PCA10121 PCB layout using this link.
From Murata SWF connector datasheet, it says
https://www.murata.com/-/media/webrenewal/support/library...
Hi,
I am using NCS 2.1.2 with the [email protected] (but I have tested with 2.2.0-rc1 and it doesn't change anything). I have attached a simple example which should just...
Hi team,
I want know how many UART modules on nRF52840 microcontroller? I am confused with one UART and two UARTEs.
Which one is connected to "USB for interface MCU" connector...
Hi,
I have successfully followed the guide for setting up the AWS asset tracker application ( https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v2.1.x/docs...
Hi all,
I did add a reset switch on my custom board. I read some topics how to active it, but I´m not sure if I did it right.
I did add it in the preprocessor define:...
Hi Nordic,
Soft device is s140
SDK version is: nRF5_SDK_17.1.0_ddde560
Bootloader - Secure bootloader.
We are trying buttonless DFU process using secure bootloader...
Hello,
We are trying to use the nrf91 GNSS with the `nrf_modem_gnss` library. I'm looking for clarification on these fields that are listed in `struct nrf_modem_gnss_agps_data_location...
test setup
the custom board schematic
we tried to flash the custom board with the beacon sample here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr...
I just upacked my new nRF52 DK and installed what I think are all the goodies to do development (on my Windows 11 laptop). I can see the board with the Programmer and I loaded...
Hi
I am using 4 x AD7410 in each TWI channel, using both TWI ports. So, altogether 8 AD7410s. ( I used the Adafruit breakout boards).
Initially I get the temperature readings...
The BOOT_SERIAL_WAIT_FOR_DFU feature is meant to wait a number of milliseconds (500 by default) for a message via serial comms. If it doesn't receive a message it continues...
Hello,
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
