Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
While using the at_client sample, when the SMS is received, the following notification is seen
How can I have the access to these notification in other application...
Hi all,
I was recently asked about using L2CAP Connection-Oriented Channel (CoC) to increase thru-put of a project. This must be a gap in my knowledge as L2CAP was always...
Hello,
I've a query.
I am trying to build and see output of " Power Management Example".
C:\nrf_sdk52\DeviceDownload\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560...
Hi! We are trying to send an HTTP request to our AWS Web Server. The problem that we are figuring out now is that we don't know the way to add a body to our request. We based...
Hello, I am trying to set up my Thingy91. I am using the latest modem firmware mfw_nrf9160_1.3.2 and have also successfully updated it with the J-Link EDU Mini as described...
To the kind attention of Nordic support team,
I have a project that is exploiting either gzll or BLE protocol. I'm using gzll_nrf52840_sd_resources_gcc.a libraries, that...
Hi, Following my previous ticket on the matter, , I have attempted to DFU an MITM bonded device to LESC code, such that the peripheral device will disconnect connections that...
I used the nrf edge impulse app and a nrf53 to collect and build a first model to detect a state of a dishwasher. After deploying it and seeing the interference method, i...
The are some examples that explain how to use the driver ieee80215_dw1000?
There are is a ble profile that can be used for the managment of the UWB devices?
Best Regards...
Hi,
I have an error with the new SDK Version 2.1
This concerns the implementation of the LTE configuration:
My prj.conf:
# LTE-M (LTE-CatM1)
CONFIG_LTE_LINK_CONTROL...
In ESB, what is the function of esb_config. selective_auto_ack? What is the relationship between esb_config. selective_auto_ack and esb_payload.noack ?
Hello,
I'm using the Fanstel BC832 module which contains Nordic's nRF52832 BLE chip on a custom PCB board. When trying to run the Blinky example on PlatformIO, it works...
Hello,
we are debugging the asset_tracker_v2 on nRF9160 DK in VS Code with the nRF Debug backend, but unfortunately the global and static variables are not shown in the...
Hello,
Can the SAADC driver be modified to be used in a polling mode instead of interrupt?
E.g. I modify the driver to not use any interrupt(comment out interrupt enabling...
Our project uses nrf5340, and we hope to match it with two wm8904 audio chips. They communicate with each other using the I2S protocol. However, we noticed that two I2S buses...
