I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
I have an EC11 rotary encoder wired to my nRF52840 and I am trying to get readings from it using the sensor API. However, I'm having issues with (seemingly) garbage data....
Hello,
We are currently implementing a custom DFU process for one of our client. They need to be able to upgrade the cores images, which are read from an SD-card. We already...
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
I have a GSM application connecting to MQTT that worked previously refuse to work when I picked it up again to improve on it.
To make sure there isnt a problem in my firmware...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...
Hi,
I tried to send audio with a sampling frequency of 44100hz, up until this point I had been sending the default sampling frequency of 48000hz.
For this I change the...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Dear Sirs!
I need that low power comparator on input AN7 reset controller when device is in OFF mode when voltage on pin drop below threshold.
Controller powered +1.8V...
Hi Nordic team
It was heard that Matter spec v1.3 will allow Matter WiFi device to be commissioned by WiFi directly, but not bluetooth.
Was this information correct? ...
Hi
I have a project base on Nordic sample code "v2.5.0/nrf/samples/cellular/Location" and it fully work with SIM card
now I need to use Onomondo softsim to replace SIM...