Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I have been following the webinar "Developing Matter products with nRF Connect SDK" and was successfully able to build the matter lock sample and flash to my nrf52840...
I got PPK2, connected it to Windows 10 PC and it is recognized as "nRF Connect USB CDC COM5". LEDs turn on Grenn color but immediately fade out and becomes red and stays like...
I would to like to update a nrf52833 controller via DFU from another nrf52833 controller via BLE. nrf52833 eval kit is able to connect with another nrf52833 custom controller...
Hi everyone, I am working with nrf 9160 Development Kit. I use LTE LINK MONITOR Unfortunately I am not able to connect to a LTE-NB network. I have updated the Modem Firmware...
I realize that this question will be stupid simple. I can program AVR microcontrollers with no trouble. The setup in the Segger embedded studio seems far more cumbersome....
Hello,
I have nRF52811 project which I would like to transfer to nRF52805. It is using SDK 15.3.
I saw this tutorial: https://devzone.nordicsemi.com/guides/short-range...
Good day!
Time after time I catch next assert
Assert occurs most often when I use 3+ mesh sensors in one server with periodic publication configured.
Is there any...
Now I'm using nrf52840 as a master and some other ble chips as multi peripherals.
As I know, in ble link layer data header, there is a tag: MD(More Data) , by which, every...
I installed nRF Connect Desktop. Opened Tool Manager. After sucessful installation, I tried to create ny first project by opening SES through nRF. The selections used are...
Hi,
I am using the ppk II, and I have had a number of occasions where the current displayed on the PC suddenly disappears (see attached). The voltage to the DUT seems...
Hi,
I'm testing the nRF9160 GPS performance with a GPS simulator. I set the output power to -130 dBm and test the nRF9160DK conductively. I made some small modifications...
Is there any guide or sample how to run unity tests on a target device instead of the native_posix device?
In general unity however cmock support on-device testing like...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
I want to use dynamic memory allocation. After searching these forums, I see the following options:
malloc
k_malloc
nrf_malloc
balloc
I haven't had success with...
Hello everyone I hope you all had a good start to the week. I am stuck with an issue I don't quite get. I wrote code with BLE, FreeRTOS, and GPIOTE as a "proof of concept...
