Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi guys,
I am using nRF5 SDK for Mesh v4.2.0 and I implemented this simple message model which can enable the communication between LPN and server node. After my nodes are...
Hi everyone, I see in nRF5 SDK 16.0.0, a Button/Led/Timer assign for handler, like that: bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler); Or: app_timer_create...
Hello,
I was working on buttonless dfu feature. I add buttonless dfu service as shown as ble_app_buttonless_dfu example and i manage to perform a ota dfu on nrf52 devkit...
Dear Sir.
Moving to version 2.4.99 from version 1.2.0 .
In previous version SPI worked well , cs was configured in overlay as
&spi3 { status = "okay"; compatible...
Hi,
I was evaluating FOTA on nRF5340 as possible upgrade to 52 series. All went good which I'm happy of.
However application size is limited roughly to half flash size...
Dear Community;
We are trying to send data via Lora using a nRF9160. The Lora transreceiver we are using is a RFM95W(Semtech SX1272). There are samples of code to receive...
Hi all,
I'm trying to set up my nRF52840 Dongle as a BLE Sniffer. I've followed the setup instructions from "nRF Sniffer for Bluetooth LE-- User Guide" v3.2, and I'm using...
Hi DevZone Team,
Is there a way to stop the ZigBee network steering after a device has successfully joined instead of waiting for the timeout to expire?
Thanks
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
Dear Nordic Technical Support Team,
I am developing a Mesh consisting of a client requesting to a net (group) of server nodes some motion data (which triggers automatically...
