Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
I'm looking into the best way to split an application implementing a LwM2M stack over 6LoWPAN between the network and application cores of the nrf5340. I fell like the most...
I have an nRF51 based Bluefruit LE Friend device with the Nordic V3 BLE sniffer firmware installed. I am using the associated Nordic BLE interface with Wireshark 3.2.5 (64bit...
Hi everyone.
I know this is gonna be a long story, thank you for your patience...
I have successfully utilized a few examples in the SDK15.3 directory on my PCA10056...
Hello
I have an interesting problem from the ble_app_uart example modified to work with spis.
ble_nus.c code
In the ble_nus.c code (above) I modified to enable notifications...
I have some question about the scan timing, referring to the documentation here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fmultilink_scheduling...
Hello Guys,
I am running an application which is sampling 3 ADC channels at 50 MHz. I am using sample buffers of size 150 and PPI to generate a sample event every 20 microseconds...
Hello,
I found one thread on this issue
https://devzone.nordicsemi.com/f/nordic-q-a/12029/segger-embedded-studio---unplaced_sections-problem
I have added the below linker...
Hi I am new to the SDK and I am working through the examples. I am currently looking at the UART example under examples/peripheral. Iam seeing that both the virtual comm port...
Hi,
I would like to ask, if I just want to "Download program", what components on the schematic diagram are needed?
Download program is OK, so first make sure that...
Hi all,
I've found an alexa gadget example but I can't seem to get it running on my nRF52840-DK. The example I've found was located under repository:
https://github.com...
nrfx_gpiote_irq_handler() which is nearly 150 lines of code. All the GPIOs seems to have same priority at the hardware level, how among different GPIO's Interrupts are processed...
