I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I have been using UART0 to implement a very simple console using console_getline_init() and console_getline().
So the nRF5340 receives commands over UART0 and outputs printf...
We're building a cryptocurrency hardware wallet. And we're using the secure bootloader provided by nrf5 SDK, to only upload signed firmwares to the device. We are using nodejs...
Hi guys,
I am working with nRF52832 board and Zephyr for a short period of time and I really don't have to much experience. Every day I learn some new things and try to...
Hello,
We have a custom board of nRF52832 with two buttons and right now Buttonless DFU is also working perfectly. But, we have scenario where if combination of two buttons...
Please help with writing to flash. If SoftDevice is off all ok. If SoftDevice is enabled, the sd_evt_get function always returns the value 5.
Here is the test code:
Hi!
We are developing a tracker based on Thingy91 using GPS and LTE. We're using the latest Modem firmware 1.2 and Zephyr/NCS v1.2.0
The GPS cold start until receiving...
Hi Devzone!
I'm trying to monitor the battery level of Lithium Ion battery.
I'm using SAADC to check the voltage of 3.7v 3500mAh Lithium Ion battery.
The battery...
when I am waiting for an event the current consumption is becoming ~180uA continuously.
I am waiting for an event using the following function
void deep_sleep(void) {...
Hi All,
I would know, is the NRF52 BLE Mesh Bluetooth 5.0 qualified or not. I did not find it anywhere. As I can see the in Cypress website, they clearly mentioned that...
Can somebody please measure and post the dimensions of the nRF9160 DK please.
Either they are not in the SPEC, or i cant find them.
either way W x L x H - would be appreciated...
Is there a way to specify which AIN should be used through the devicetree API? For example, here is a code snippet:
How would I use the devicetree API to replace the NRF_SAADC_INPUT_AIN6...
Hi
regarding the Nordic guidelines for aQFN, it recommends to use 0.305/0.61 for through hole via.
We are using 0.2/0.4 to avoid soldering bridge and non find any issue...
Hi,
I've tried the Heart Rate sample code (both from hex and source file) and in both cases, I encounter the same problem - constant disconnection. When it finally connects...
Hey, so I have been working on developing a BLE central device on a Raspberry Pi using the bluepy library. It's a pretty simple application, I just need it to scan and interface...
I tried to launch your example "Bluetooth: Mesh Light" using nRF5340 PDK and I failed. I followed this guide developer.nordicsemi.com/.../README.html . Also I tried to launch...
