Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
Sir
about the
while(1)
{
sd_app_event_wait(); //stay here until a interrupt or connection occurs...
}
During the time that there is not a interrupt and no connections...
Hi,
I've recently switched some prototype code from using MQTT to a custom UDP-based protocol. What I noticed is that if I have the unit sleep for longer periods of time...
Is it allowed and possible to change the configuration of one pin from input to output chararacteristic (and back) during the normal work flow. I need this possibility for...
Howdy,
To achieve the lowest possible power consumption on the nrf9160, it is noted that it is necessary to disable the UARTs that are not used, when in sleep mode. However...
I'm unable to write a softdevice to my nrf52840, can someone please point me in the right direction?
I was able to program the board just fine using nRFGo Studio, but I...
Hi, I am using Adafruit BLE sniffer with nRF51822 v2 firmware and I am sniffing BLE packets in Wireshark. I can see my devices advertisement data when my device is in the...
Hello,
We are using the nrf connect Android app in order to scan and connect to ble peripherals.
The scan procedure is executed perfectly as we can identify and connect...
Hi In v5 one can advertise in le_coded and then a central can connect off the resulting AUX packet.
For the AUX_CONNECT packet the inter-packet delay is T_MAFS which is...
When I read Objective Product Specification v0.7.1, it seems external pull-up resistors are required.
However, when I use TWIM without them, it works out.
Do I need...
Hi Everyone,
I am using nRF52832 with SDK v14.2 and SD v5.0.0 on a custom chip.
Recently i included DFU support to our application. It turns out that secure bootloader...
Hi, I'm new to nRF52480 and Nordic SDK. It is first time for me when SDK has one big config file sdk_config.h. I started playing with examples (LEDs, serial I2C) and get it...
I am developing a PCB that contains this schematic, I can run the sw code on the nrf52832 and use the pinout, but I can't connect to nrf52832 via ble communication. I think...
Hi. My product uses nRF52840 as a beacon transmitting every 3 seconds at max power of +8dBm fed to an antenna of gain 2dBi. Is SAR testing needed for my product? Product is...
