I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi, I'm looking for a way to communicate with Blue tooth. I need a low footprint chip that allows for a BT HID gamepad application. I'd prefer to communicate via i2c, or some...
My application uses the nRF51822 with a GPIO configured as output and another GPIO is configured as input. Connected to the GPIO_OUT is a resistive load (Rload) which then...
Hi, we switched from your competition to your platform. I know you wrote somewhere that you cannot provide examples for every sensor out there. But your Nordic Dev Zone is...
I have run many tests using the light_switch demo. I have noticed that occasionally the latency is much larger. The latency jump is between sends, i.e. it will send 20 times...
I am using 3 mobiles for testing
1. One Plus 6
2. Samsung Galaxy Note 8 or Google Pixel
When I connect my hardware with #1 phone and send some data from the nRF Connect...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
Hi,
our installed base of sensors transmit their data in periodic BLE 4.0 beacons. I would like to develop a relay board that receives these beacons, and then retransmits...
Hi,
I want to use the nRF9160 DK for an NB-IoT application. I am located in Bavaria, Germany where there is no LTE-M coverage. I understand that I need the NB-IoT version...
To the kind attention of Nordic support team, from www.nordicsemi.com/ I downloaded all nRF24 Files.
I found very interesting the nRFgo Motherboard (nRF6310 Rev 1.4) pinout...
Hello ,
I am new to nrf52832
i am using external interrupt for led on and off
here the problem is when i press the button 1 led will turned on if i press the same button...
For Zigbee RF manufacture test, we did try nRF52840 using the sample code "radio_test" in SDK nRF5_SDK_15.3.0_59ac345,
but it seems that only the TX power information can...
Hi all,
I'm developing a buttonless DFU based application using the SDK v15.3 Following the documentation was pretty easy and I'm now able to run the app_ble_buttonless_dfu...
Hello All,
I am working on nRF51822. Use nRF51 SDk 12.3.0 version for reference. Writing program in IAR in windows.
Porting the OTA DFU to my custom APP.
use SDK 12...
Hello
I am developing a product by using nrf52840 and s340.
I know the way how to certificate ble. It is using the dtm example.
But I don't know how to certificate...
