Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello Nordic ,
Do i need to implement the config_ client model so that the node can be named as a client and a provisionner in same time ???
however in the example of...
I am using SDK 15.2 with IAR's EWARM 8.30.1 and the nRF52840 Development Kit. My eventual target is the nRF52-Dongle. If it matters my development OS is Windows 7 64-bit....
I would like to write code to disconnect from any connected device. My system is a ble peripheral with s132 6.0.0.
My code calls:
result=sd_ble_gap_disconnect(BLE_CONN_HANDLE_ALL...
I starting working with examples for the nRF9160. Zyphr seems like a very complicated OS (like Linux with device trees, etc) and difficult to use with a debugger.
Is the...
Hi,
I trying to convert a stm32 function code to nRF52. The goal is to use a spi periperal on my custom board.
In this application we need to have 2 bytes transfert. That...
I can communicate with success from the pc to my custom nrf52832 device (SDK 15.2, S132v6.1) using the pc-ble-driver (sd_api_v3) with Tag 4.0.0 from Github. Great work!
...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
