Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am trying to run the debug project for ble_app_hrs following the steps in "nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1.pdf"
but I get this error...
Given that most of the SDK (including the softdevice hex) is public now due to the mbed support: would it be possible to open up the downloads for the standard nRF51 SDK and...
From the s130 release notes:
GAP
Concurrent Central, Peripheral,
Broadcaster and Observer operation
(DRGN-4354).
Up to 4 simultaneous
active connections...
Hi.
I am trying to modify the bootloader example provided by nordic.
I am able to compile/link my code and use nRFgo studio to run it, but for some reason I can not debug...
Hello,
i´m using nRF51822 with S110 SoftDevice to transfer data from Sensors that will be read out via I2C by the Nrf51822.
I have read some topics about how it is not...
Hi,
I bought nordic evaluation board 2 days ago. I have been searching through the forums to enable and test the voltage level of a battery and monitor it via UART. After...
Hello all,
Is it possible for a nRF51822 to read information from another peripheral Device using broadcasts or advertisments?
I have an application where I need to...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
I have download the puck-central-android code from the following link
github.com/.../puck-central-android
I can build the project and successfully programmed in the android...
