I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi, in our project with the nRF5340 we desire use the nRF21540 to have a long conection for BLE, the problem is we don't have any pin free in the nRF5340 to manage the nRF21540...
I have configured new UART in zephyr.dts device tree like this" "/ { chosen { zephyr,console = &uart1; zephyr,shell-uart = &uart1; zephyr,uart-mcumgr = &uart1; zephyr,bt-mon...
my device acts as ble periph ,case BLE_GAP_EVT_DISCONNECTED in ble_evt_handler , if do m_conn_handle = BLE_CONN_HANDLE_INVALID,current changed to 2.5mA, if dont, current is...
Hi,How can I force mcuboot to use a specific serial port for logging?
chosen {
zephyr,uart-mcumgr = & uart0 ;
zephyr,console = & uart1 ;
zephyr,shell-uart = & uart1...
Hi,
we have created a new product prototype where audio streaming is the functionality. 2 different HW revisions were so far built, the software originally is built to use...
I am trying to make the broadcast _audio _sink work . It is always stuck with the following logs :
Broadcast Sink created, waiting for BASE
which then times out with ...
We built a custom version of the Direct Test Mode sample in our firmware, using the USB shell to interface with the test operations and removing the UART or HCI interface...
I have a IMU whose interrupt is connected to GPIO0.11 which is also nrf-gpio-forwarder GPIO (which I dont use)
I managed to get it to work but lost that progress and cant...
Dear Nordic
Question 1: How many bytes can the Rf Tx of the current Nrf52810-QFAA transmit at a time? Now I can only send 256 bytes at a time. Can I send 512 bytes at a...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
