Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I'm using Zephyr controller instead of Nordic's Softdevice to use the DTM HCI feature in the Zephyr controller. Before switching to Zephyr controller, the application...
I want to be able to select the Network Coordinator Zigbee channel based on some GPIOs state (switches).
Is there any api function to set CONFIG_ZIGBEE_CHANNEL at runtime...
I am use sample "Bluetooth: Peripheral HR" as the base app
and added these settings to `prj.conf` on both central and peripheral sides
but I still got the...
Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hello nRF team. Is there any different bewteen passing AT command and directly calling the Modem lbraries APIs(from nRF Connect SDK v2.5.2) to control the modem? For example...
Currently our product shipped with SD132 7.0.1, and bootloader/dfu compiled with SDK 16.0.0
We are testing update the bootloader on production devices, and want know how...
Hi Team, I am trying to do DTM test in NRF 52840 using Zephyr- os .The DTM code is working fine on my dev kit ( NRF 52832).I compiled DTM code for NRF 52840 and changed the...
Hi,
I have a problem with sending over NB-IoT to a cloud service. I have found that the helt of my messages only arrive in the AWS cloud and it seems like the modem also...
Hi Support Team
We use ncs to develop nRF52840 application and want to know how many low power mode do ncs have and how to enter these low power mode.We want the nRF52840...
Hello,
We are searching for a board that supports Angle of Arrival(AOA) and Angle of Departure (AOD) for conducted mode radio testing.We need a board euipped with an antenna...
Dear Nordic team
I have the following code for testing the SPIM function of nRF52832.
NRF_SPIM1->EVENTS_END = 0U; NRF_SPIM1->ENABLE = 0; NRF_SPIM1->ENABLE = (SPIM_ENABLE_ENABLE_Enabled...
Hi Nordic .
We are developing an application with nRF5340. In this application, we need to use the SPI Slave feature. According to the documentation, there isn't a clear...
Hi everybody I'm using sample bluetooth peripheral with sdk v2.6.1 and toolchain v2.6.1 to load with nrf5340 but it doesn't seem to build, I see the library has changed from...
Hi,
I am looking into adding BLE OTA firmware update functionality and started by exploring the example provided in Nordic SDK (SDK v16.0.0) while following the documentation...
i'm trying to get an interrupt using sensor lis2dw12 , i have connected my int1 pin of sensor to my gpio 0.10. whenever data is ready it should give me an interrupt this is...
