I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
hi Nordic
i am working with nrf52832
i have a code that works with SDK11.0, softdevice132
i am migrating my application for the same boards to run on zephyr, ncs v2...
Hi,
I want to use the nRF52810 hardware IIC as slave to communicate with the hardware IIC as host nRF52832. Is there any routine or documentation on how to use nRF52810...
My server gets a write request to a characteristic that has not been enabled.
I respond with
However, the value of BLE_GATT_STATUS_ATTERR_CPS_CCCD_CONFIG_ERROR is...
I used STM32f767 as the BLE host to compile the central demo, and the execution program encountered a similar error.
cmd:west build -b nucleo_f767zi samples/bluetooth/centra...
I am using nrf52832 and developing with FreeRTOS. I want to use Bluetooth and control a WS2812 LED strip simultaneously. When I don't start Bluetooth, i.e. //nrf_sdh_freertos_init...
Hi
I am evaluating openthread with NRF52840 and currently I am trying to broadcast continuous udp messages in for loop. But I am facing the issue that cannot be to send...
I'm using Windows 11, WSL2, VSCode extension, NCS v2.
I am trying to use a Pipe from an ISR and I appear to be crashing the system as a result.
The assertion seems...
Hello.
I tried to implement GPIOTE on GPIO1.x, but it seems to not work.
How to reproduce at below.
At first, I generate nrfx sample project.
Just be sure, I compile...
Hi,
SDK 17.1.0
Q1:
I have integrate ble peripheral on ble center to been both of center and peripheral role, it seems works normally. But the length of advertsing...
Hi, I am working on a costom PCB with the nRF52840 as microcontroller. For the antenna we want to use the reference design from the dongle (pca10059). We are using OrCAD to...
Hi,
Is there any AMQP opensource (rabbitMQ) ported to Zephyr NCS for working with LTE/nb-iot on nRF9160 SIP?
This porting will help us much on our current project.
Thank...
I use a nRF9160 DK rev 1.1.0, nRF9160 DK rev 1.1.0, mfw_nrf9160_1.3.4 with NCS-2.1.2.
If I press "Button 1" and reset the device, it sticks at
"*** Booting Zephyr OS build...
Windows 11 WSL2, NCS 2, VSCode
I want to be able to trigger a reboot from both hardware and software.
I am able to do this when I flash my code directly from VSCode to...
We have a requirement for 4 PDM microphones in our IOT/BLE application but from looking in more detail at the specs for both the nRF5340 (and the other nRF52xxx) parts see...
I want to get the peripheral side of my dual-role gateway device to accept ONLY NFC (LESC) pairing from my Android phone.
I have had NFC working but it seems I keep breaking...