I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
I am new to the nordic family. I am trying to bring up the UART1 in 9160 DK but it's not working. The same code works for UART0 appropriately.
And the code...
Hi, Our company is considering to seup a linux gateway to support BLE mesh/Thread/Zigbee with nRF52840. We want to use the binary file from Nordic directly which could support...
Hi,
I've got a custom board with an ENC424J600 connected to an nRF52840. I started with nRF Connect v2.0.0 but I've since upgraded to the latest (v2.3.0-rc1) to see if it...
What data do we need to save? (provisioning data after ECDHSecret and becon mac address? )
And how to put the data to the new devece?
I hope i can get some API and data_name...
I want to get the api to do some logic operation.
in SDK I know it will "enter_bootloader(p_dfu) " then " nrf_dfu_settings_write ",
But in NCS1.5.1, It's hard for me to...
I wish to take IQ samples in the regular payload of a packet sent and received using the RADIO peripheral.
It seems all the IQ sampling support is tied to the CTE portion...
Hi, I am currently working on a project that requires ESP32 as a client and nrf52833 as a server. I use SDK 17.1.0 with softdevice 7.2.0.
When I connect to nrf52833 with...
I have no experience of Nordic harware or software - yet - it seems pretty good at first sight. I have a potential application which requires being able to read an attached...
Has a software driver for infrared (IR) communication been developed? I require a driver to transmit remote control data via IR LEDs, and I am surprised that an appropriate...
Hello, I am trying to test the DTM firmware on my nrf52832 device using the DTM example for pca10040 under SDK 15.0.0 As a test I have been using the GUI found on https:/...
Hello,
I have some troubles understanding the design of the MTU exchange within the Android Nordic Library.
We are using a NRF52840 SDK 17 softdevice version 7.2.0 and...
I paired nRF5340 audio DK gateway with Earfun Air Pro 3 earbuds. I found the gateway went through stream_configured, stream_qos_set, and stream enable more than Samsung Galaxy...
When IPC message services are being used for message passing between application and network CPUs (for example):
CONFIG_IPC_SERVICE=y
CONFIG_IPC_SERVICE_BACKEND_RPMSG...
When I start the sta example with my FRITZ!Box 5490 router I can only ping the device once. After that the nRF7002-DK does not return the ping, nor does it print any error...
Hello,
I am looking for an example which uses nrf-spim driver in Zephyr environment. I am currently working with nrf9160 board, and this device has configured by default...