Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Good day everyone !
Can thingy 52 itself be used as a location tracker, from Received Signal Strength Indicator(RSSI) . Does it have this function ? If it does, may i...
Hi all,
First of all, this is a new field for me, so I'm quite a beginner here. I'm connecting my ESP32 to wifi and I want to send somehow the IP it connects to, to the...
Hello,
In my application (SDK, 16.0.0, nRF 52840) I need to enable the DFU service after initialization, which I do by exposing a custom service "DFU enable". This in turn...
I'm currently using Zephyr with Nordic Segger v5.50c.
Most of the code uses NRF_LOG, NRF_ERR statements which are printed to the Nordic Segger terminal.
I also configured...
Hi,
We are trying to update the S112 softdevice on nrf52811 over serial DFU but it's not working and throwing the below errors.
We are using nRF5_SDK_17.1.0 and soft...
Goodday,
For some reason my nrf Connect Programmer stopped working after doing the latest updates. To test I took a brand new dongle, Programmer picks it up but does not...
Hello, i have send my program with my DKnr52840 on my module 805, (the example peripheral Uart) now i would like to make my com with putty or other software but i'm going...
Hello,
The company I work for uses an nRF52840 PCBA for one of its project. During production, the board will be placed under test using a custom-built fixture. Due to the...
Hi,
For my application I am supposed to evaluate if nordic SPIM & SPIS drivers are working on interrupts..? In the driver file "nrfx_spim.c" I observed the below code...
Hi,
I have some questions regarding DFU:
Does it have its own BLE hardware?
Does it have its own processor? Or it's part of the main one?
Can we synchronize between...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
Hi I am recently working on Enhanced Shock Burst (ESB) protocol. where PTX and PRX
and
PRX will communicate upto 8 PTX
i have a question like how a single device will...
I'm working on porting some Arduino code for a Crystalfontz 320x240 FT810 display to run on the nRF9160DK. I'm having some success, But it seems Zephyr has an FT8XX driver...
I use a example application from SDK_DIR\examples\ble_peripheral\ble_app_template\pca10056 base on nRF5 SDK v17.1.0,then use SDK_DIR\examples\dfu\secure_bootloader\pca10056_s140_ble_debug...
