Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi,
I am trying to upload HEX files to a nrf52832 (on a Sparkfun Breakout board) with a nRF52 DK. The problem is nRF Connect Programmer don't recognize them.
I installed...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
In sdk_config.h, BLE_ADVERTISING_ENABLED is not...
Hi, I'm currently in trouble with the sd_flash_write function. I've already a library using this function running on the nRF52832 with the S132 softdevice. But when a tries...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
Hey,
I'm trying to put the nRF9160 into System Off mode and am getting a bus fault error when writing to the REGULATORS module. This is the error output:
***** BUS...
Hello everyone,
I try to import a project from Keil to SES,
I 'v read the instructions in this article.
Segger Embedded Studio - A Cross Platform IDE
Generally I have...
HI:
I'm using a cli routine from the SDK，and I register the callback function zcl_device_cb() with ZB_ZCL_REGISTER_DEVICE_CB()，But whatever message I receive does not go...
Hello community,
I successfully flashed assets_tracker code into board and configure in NB-IoT using Configure NRF SDK project in segger studio.
I used Vodafone SIM card...
Hi, I use nrf52832's uart with a simple driver, not "nrf_drv_uart", because I don't know how to use receive and transmit interruption with "nrf_drv_uart". the uart drive i...
Is there a supported way of doing an unsecure flash (the nRF is hardwired via UART to a secure processor) without rebooting?
The HW design the nRF is integrated with uses...
I am using the nRF52840 DK to read data from an IMU sensor (STm LSM9DS1 9DOF). Like most sensors, you transmit the register number first (on MOSI), then continue clocking...
Hi,
I am trying to develop models using the Specifications. I came across generic battery model which was using 24-bit values, time model which was using 15-bit and 40-bit...
Hi,
I've modified the SDCard example to write every 2 seconds 80 bytes to a SD Card. The SDCard is correctly mounted and the File is opened and kept open.
After several...
Hi,
Sorry if my english isn't perfect but I have a quick question and I could't find a good answer for what I'm looking for. I'm using a FPGA Arty S7 as a SPI master and...
Hello Nordic team
I have tested individual "record text" NFC example and buttonless dfu example with SDKv-15 and both example are working. Now I am trying to merge both...
