Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello Nordic,
As the subject states, why are these two modules still experimental? From what I can see, they were introduced as early as SDK 10.0.0 which was at least 3...
Hello,
for our device we have an input PIN defined with GPIOTE, we expect an event when this input PIN goes from High to Low (interrupt is set by another device on the...
We're using the nRF52832 and want to trap if various parts of RAM are ever executed. We'd like to restrict as much as possible. We run nRF SDK 14.0.0 and SD132v5.
Seeing...
Hi,
I want to migrate BLE HRS peripheral sample to custom board with Raytac's MDBT42-512KV2 (WLCSP nrf52832 used). The board doesn't have external XTAL.
In sdk_config...
I have a problem with understanding reference layout for the chip antenna I want to use in my project. The antenna is ANT016008LCS2442MA2 from TDK.
Based on the schematic...
In my application, I'm setting a message as manufacturer's data to be sent with the advertising message. To do that is simple, since I have a data type ble_advdata_t , and...
Hello guys, I was doing some testing with the QSPI component, and noticed exceptionally high current draws depending on whether the Peripheral was on, off, and if the Macronix...
I’m designing a board with nrf52840. For the RF layout part I’ve followed the reference design apart 3 pads near the pcb antenna.
The question is: How much is indicatively...
working environment:
SDK:12.3
WIN8.1
hardware:nrf51822_qfaa
nrfjprog:9.8.1
problem:
using nrfjprog to program application(s130 + bootloader + application),application...
Hi,guys
I got a problem. I tried to create a service to control led over BLE, when i finished, it can advertise, everything was ok. But when i tried to write 0x01 to control...
BT832 connect to a passiv MEATER temperature senor. How should I configure the Device with AT-commands. I use Docklight to send AT-Commands from my BT832.
Hi Team,
I want to connect the nRF52832 based custom board to AWS-IoT cloud.
The Simcom 2G module is interfaced with nRF52832 over UART.
Can someone guide me from where...
hello everybody,
In my application i want to check if a password is set, to enter bootloader, otherwise don't start the bootloader.
This should work without bonding. ...
Hi, I'm new in the use and development of chip.W here do i start to develop myself?
eg my first aim is to make bluetooth headset compatible with android. Can you help me...
Hi, I have been looking at the following document nRF9160_OPS_v0.7.1-1510217.pdf which I had downloaded from the Nordic website today. In particular the layout guidelines...
