1. Set up the development environment for the nRF52840 chip in VS Code, but encountered an issue where the chip could not be recognized. The development environment consists...
Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi there,
How could I receive a large data from phone, example 120 bytes from a characteristic. So far I was able to receive 20 bytes.
From the working code of 20 bytes...
Hi
Try to send characteristic notification by invoking sd_ble_gatts_hvx() with the following parameters:
uint32_t err_code = NRF_SUCCESS;
ble_gatts_hvx_params_t params;...
I do run the “nrfjprog --pinreset”,later, the nrfjprog can not find the nrf51 device,WHY?
the nrfprog version is V5.2.0,
I use nrf51822qfaa,s110,keil,etc.
Hi, Guys,
I have a question about chip operation temperature. Will the chip auto reset when the temperature over 75 C? I checked the nRF51822 product specification v3.1...
I would like to learn more about when it is safe to invoke soft device methods and when it is not. For example, are the following 'allowed' to make soft device calls to update...
Update to below: I get data out of the VCP and into Termite for a sub-second when I first power the board (with handshaking enabled), then I get no subsequent data (even though...
Hi,
I have just received a bunch of N550 modules and now I want to try and see if it is possible to update the firmware of these devices without using a JTAG.
If I understand...
I wrote my own ACI interfacing code, so I have questions about some details of the data credit system that most devs may be insulated from by the Nordic SDK.
Section 25...
Hi All,
I was wondering if it was possible to program the nrf51x22 in c++? I am using Keil and I'm trying to convert the examples in the SDK to CPP by adding --cpp to the...
hi,
I have used sd_flash_write() in my code. The scenario is that sd_flash_write() will be called after a DISCONNECT event. And it would wait for system events :
NRF_EVT_FLASH_OPERATION_SUCCESS...
Running S120 2.0 central on nRF51422 QFAAE0 (1504CH) and when I call scan_start() i'm getting 0xDEADBEEF at line 431 in file src\ll_lm.m0.c"
Can anybody shed some light on...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
Hello all, to optimize the BOM and size of our device(Tag based on nRF51822), the external divider was replaced by software configuration to measure the battery voltage. In...
Hello,
I have seen, that the BLE MAC is increased by one, in dfu_transport_update_start() (dfu_transport_ble.c).
Can someone give me a short explanation, why this is done...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
