hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
Hi
We use the nRF51822 with s110 active. As long the s100 isn't active, we can debug, set breakpoints, stop, continue like it should work.
When activating the s110 and...
Hello,
The question is about CUSTOMER area in UICR. After locking chip wirh UICR.RBPCONF.PALL I noticed that I still able to read UICR.CUSTOMER data.
Could I enable readback...
Hi all,
Google launch uWeave Library project.
uWeave is an implementation of the Weave protocol intended for use on microcontroller based devices.First demo project is using...
Hi,
As first stage of planning our next generation of wireless sensors at my workplace, I must carefully consider which radio protocol suits us best. We don't need sub 1...
HI,
Hi,
I have been working on nRF5 Development Kit where Basic configuration is working i.e. blinky program and when I load peripheral program(PWM,UART), its also working...
Hello. I have several nRF51 devices (nRF51 Dongle, pca10031) I wish to use as BLE link between robots.
Is there any examples or tutorials that show how I can do this...
