Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hello,
I am experiencing an issue while trying to connect an external flash memory (MX25R64) via the QSPI interface on an nRF52840-based custom board. My pin configuration...
Hi.
I wanna evaluate nRF52840-DK. However, when I tried to install Toolchain on Visual Studio Code, a message "Failed to fetch available toolchains." is displayed. "nRF...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Greetings to everyone.
We have the nRF52840-DK, where the Power Switch SW8 physically is broken.
Is there any way (a bypass, making a bridge/shortcut, using a soldering...
HI everybody,
I have problem with my Nordic nrf9151-DK. I am not able to use GNSS with this kit. A looked at documentation and found, that i have to activate XCOEX0...
Hi,
I have been using the nRF52840 for a long time, and everything was working fine. However, now LED5 starts blinking whenever the USB is connected to J2. I have tried...