Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello, I'm working with the event manager doing a customized Asset Tracking version firmware. The problem is that when I attempt to submit an event with an array with fixed...
Hi,
In my system I have a timer that ticks at 1kHz frequency, collects some data and sends it over BLE via bt_nus_send. It works fine, but in the beginning of the stream...
I want to incoorperate the pc-ble-driver into a product, using the PCA10059 USB-dongle. My design requires me to receive advertising scan responses. I successfully receive...
Hi,
I'm using nRF Connect SDK 1.7.1 with nRF52833dk.
I'd like to implement DFU over UART.
I see a number of examples to achieve this with SDK5, but not with nRF Connect...
Hi,
I would like to know how much noise I have to expect with the SAADC.
I tried the example "saadc_pca10036" and attached the pin P0.02 (AIN0) to a ground pin on the...
Hi,
I have a project with 3 threads running on a nRF9160. I am using nRF Connect SDK v1.8.0. Basically I borrowed the code from "mqtt_simple", "location" and "threads"....
Hi all,
I am working on a project which needs dwm1001 library integration with nrf52 ble code. I am using ble_app_uart code. decawave have provided dwm.o and libdwm.a...
I have an issue compiling the example code from SDK 17.1.0 using Microsoft Visual Studio Code in Windows 10. Using the easiest example possible, after starting a terminal...
Hi Nordic,
I'm able to do dfu without validation after few days of studying documentations and forum.
Here is the settings page i'm flashing:
But i had to disable...
Hello all,
the sensor is selected and so far powered via an external power supply, while the nrf52dk is powered via the USB, however, I am not sure how to properly organize...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
Recently I just found that when clicking the flash option in the vscode, the IDE only builds...
Hi,
I'm using the saadc and I notice that the max value that saadc can convert is 3,3V. If I try to convert an higher value, the result has no sense. For my project, I need...
Currently I am working on a open thread project.
Right now I am facing an issue in which my board/code is getting reset every time after I have done some changes in my previous...
Hello,
Currently In customized PCB board, nRF52832 is connected to both HFCLK(32MHz) and LFCLK(32MHz).
It takes up too much space. So HW engineer asked me to consider...
Hello. I have a device that connects to desktop app through usbuart-to-ble converter and I'm trying to simulate it using nrf52832. I've started from ble_blinky example using...
