I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
We are using the nRF5340 for Thread communication and an Ignion BLE Antenna (NN02-101) for range testing.
During the range test, we observed an RSSI of -25 dBm at close...
Hi all,
In our project we are using two device running on NRF chipset. One has the s140 softdevice version ( NRF52833 ) and the other has s112 version ( NRF52810 ). We are...
Hi,
I need help to disable shell_uart and its commands used in UART of BLE mesh chat example as i want to configure this UART for custom protocol along with RTS signal to...
Hi Nordic:
I am currently working on Bluetooth Matter product certification and require the certification materials for the nRF54L15. While filling out the application form...
I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
Hi,
The nRF9151 DK product page indicates that the DK includes among other documents the hardware schematics and layout files. I've purchased the DK kit, but as far as I...
I am trying to build an application on nRF Connect SDK on VS Code and I keep getting this error:
c:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc...
Hi All,
I am experiencing a significant voltage drop issue with the NRF-PPK2 device after a recent firmware update. When I set the source meter output to 3000mV (3.0V) at...
Hi All,
PPK2 isn't accurately measuring currents below 20 μ A, showing 0 nA instead. This started happening after you updated your nRF Connect software, and reverting...
I am using the nRF52840, nRF5_SDK_3.2.0, using example: usbd_cdc_acm. I mofified the example so that I transmit characters from a serial port to the USB using a virtual COM...
I have tried init modbus RTU on my nRF9160 with SDK2.5.2 using max485 module but i have faced an error. This is the error: *** Booting nRF Connect SDK v2.5.2 *** [00:00:00...
Hi forum ,
pls help me for flash erase ,write and read to be successful for windbond w25q64 here i m stacked a long days if possible pls send me a sample successfull code...
Hi,
I noticed that NCS has been updated to version 3.0.2. I now want to compile the beacon in host-only mode and make it work on the nRF52832, but I haven't succeeded so...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
