Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
Hi,
I have a custom board with nrf52840 with UARTE1 instance enabled for RS485 communication.
I have 2 boards on the same configuration and trying to send data to each...
Hello,
I am trying to use a nRF52840 Dongle to perform DFU over Thread: I am using a PCA10059 board, already provided with the default bootloader. I also programmed the...
Hello,
I am in a project using nRF52 board where I develop and Android app.
The application is using Android stock BLuetoothLeScanner to scan for devices. After that the...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. This bonding information is written to the flash area using...
So...I have an idle task running then a UART interrupt fires upon a character being sent over the serial, and somewhere during the execution of the ISR, it attempts to execute...
I am using the NRF9160DK, I have already made all the getting started and compiled an example to use the LEDs on the board with em studio. I had already connected my card...
Hello,
I am trying to send some sensor information via thread / mqttsn every 5 min. Therefore. The dongle has to wake up (5 sec.), send the information and return to sleep...
Hi friend,
I used SDK16.0 and softdevice is S140. I modified ble_nus_c to a custom 128-bit UUID. It has 1 service (0x0211) and 3 characteristics (0x0212, 0x0213,0x0214)...
Hi,
I'm testing the aws-FreeRTOS code.
In detail, It's a BLE test
The problem is, BLE can connetc in the test but next step (read/write) cannot
BLE connect apple...
Would it be possible to illustrate what AT commands would be required to set up and send a UDP packet for the nRF9160, including configuring the modem, turning the modem on...
I'm writing a program that receives a time from an RTC over TWI then writes that time into flash memory using the example from the flash FDS library. The problem I'm running...
Hi,
Am using nrf51822 as central, i want to discover and to commuinicate with the service of another ble module (which is RN4871 from microship).
My problem here is that...
Hi,
I'm trying to flash the firmware to some custom built pcb's with NRF52840 on it. The first time I flash it, it works great.
Then, if I try to erase the chip (or any...
