We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
nd Since i am still a newbie to nordic i wanted to know how can i break the task in smaller steps.
1)As a first step i get the values in temperature form using saadc.
...
Hi,
I am unable to find how is software interrupt generated for Softdevice.
I am able to see SD_EVT_IRQHandler()
but when this event is triggered
Sudhir Foujada...
Hi,
I am using sdk for mesh V.5 and nrf52840 dk.
I have run the serial mesh example and it worked fine.
I also modified the light switch example to send and receive...
Hi, I tried using the border router example that is provided and it works ok. I would like to install the border router software right onto a machine running ubuntu so that...
Hello! My device (peripheral) is based on nRF52840. Also, I use nRF52840 DK (central) to establish connections from the Linux side and getting of the data from the device...
Hi all,
is it possible to have the Immediate Alert client and Server at the same time? I need to have an alert from Smartphone and also to be able to send an alert to the...
Hi
In the final SLM version , please provide an option to disable and enable JTAG in software (thru AT command or by some means)
As part of security, this is needed...
Hi,
We are in the process of integrating a NRF52840 to a linux based host gateway device, which is supposed to be the gateway for another peripheral device which also run...
nrf52 dk board TWI SCANNING EXAMPLE INTERFACING WITH EXTERNAL EEPROM
Hi, this is vadivelan
I am working on a task like interfacing external EEPROM memory with nrf52dk...
Hi,
I am currently trying to a DFU where the firmware image is sent to external memory, validated and then copied to flash and executed there. I am doing this with the nrf52840...
Hi while implementing Media Transfer Protocol MTP I wanted to know how many bytes were transmitted by the host on EPOUT. I had to do a bit of research and trial/error - I...
Hi,
SDK : nRF5_SDK_15.2.0_9412b96
I want to perform pairing between mobile app and a device NRF52832 device based on the device serial number.
In other words I want...
Hello,
I come to you because I wanted to recover the GPS data in my project for that I based on the sample agps, however when I launch my project at the time of the reception...
Hello
I had integrated the DFU client stack in ble_thread_dyn_hrs_coap_srv_freertos project.
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
After clearing all the...
