I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
SDK: nRf connect SDK
Kit:nRF5340
I would like to configure a radio peripheral in application core. But radio peripheral is a feature of network core.
1. Can you...
I have implemented time synchronisation that is based on this example: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/wireless-timer...
Hello,
I am using Nordic nRF52840 (nRF5SDK v16.0.0) and softdevice : s140.
Nordic MCU is connected to Host MCU over UART interface (baudrate = 115200). I have below observation...
hello,
i am using nrf52840 with sx1276 i am trying to change some of the calls from arduino to nrf52840 can you tell me i am doing everything right
#define DIO0 NRF_GPIO_PIN_MAP...
Hi. I use NCS SDK 1.5.1 with NRF5340 .
I took the project from: \zephyr\samples\portability\cmsis_rtos_v2\philosophers\ as base and try to add two additional tasks.
Application...
Hi,
I would like to implement cell triangulation with the nRF91 in order determine the location of the device via cellular. I already had a look at the available posts such...
Hi friends:
My ble mesh gateway want to remove a mesh node
(a): Which api can i use to realize this purpose?(My SDK is nrf5_SDK_for_Mesh_v5.0.0)
(b): There is a special...
Hi Community! We're happy users of a range of Nordic solutions on behalf of our clients in Europe. Now we're facing a new challenge: one BLE device that should act as a sort...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
Hi. I am a beginner with nrf52840. Trying to get SPI and an I2C peripheral working at the same time using the SEGGER Embedded Studio. I have working version of both the I2C...
Hello,
I am using the nrf9160 to develop a cellular product but am seeing inconsistent end-to-end connectivity results. For the nrf9160-dk and a custom board based on the...
Some transciver can improve RF performance like output power and EMV, through supply higher DC voltage. Did nRF52840 have the same characteristic with BLE? Is that high votage...
