At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
Hello, Is it possible to use the USB Pins for Uart? no USB Protrocoll Would be nice if i can use the USB socket for UART with my other projects so i dont have to create a...
Hi,
There are new softdevices (v7.0.1) out for the nrf52832 and nrf52840 but, I don't see any mention of them on Nordic's infocentre. Are they compatible with SDK 16.0...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I have been working on DFU ble update with nrf52840 DK.
Using the onboard buttons I'm able to go to DFU mode where as for our custom board there's no buttons and I...
I am developing a firmware for the nRF52805 SoC with a nRF52 DK. I want to implement the DFU support on the same. The secure bootloader example in examples\dfu\secure_bootloader...
Hi everybody,
I'm trying to update a device (a PineTime device with a nrf52832). The firmware is using legacy DFU. I already have a DFU package, so, I only need to perform...
