Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I have Six services in my project to be advertised and make available to the user at a time.
first I have faced problem while advertising two vendor UUID's.I solved...
Hi! I'm planning out the connection of a micro-SD card through SPI to the nrf52840. I'm reading through the documentation and when powering the nrf using a Li-Po through VDDH...
I am trying to add a bootloader to my application which I have currently running on an nrf51822 with SDK12.3.
The first problem was that the examples from SDK12.3 do not...
Sir,
I finally got success to measure the Coin Battery using a analog INPUT of NRF52832, AIN4
i am using ZEPHYR RTOS
I have to connect the BATTERY VDD to the AIN4. ...
Looking for Android logging utility where host processor on a Mobile device is interacting with nRF52810 over UART interface.
or Provide a stand alone logging utility that...
where can i search whta the mean about <type>,<result>,<datatype>,,<qos>,<retain>.....Etc.
EX: #XMQTTEVT: 4,0
I Don't know what these values represent
thanks
...
Hi,
We're using a 51422 with s130 to perform OTA DFU.
Both bases for bootloader and central are from sdk 12.2.
We have already implemented the older DFU (non-secure...
Hi,
I want to use the Code Profiling feature from Ozone with my nRF 52840 DK and the j-Trace Pro Cortex. Compiling and debugging my program works flawless inside Segger...
I am trying to figure out how to use the TX part of the BLE NUS Service to send a notification. Currently I am receiving data via the nus_data_handler, however because i will...
Hi, I just got my nRF5340 PDK and was wondering if it is possible to develop applications for the nRF5340 PDK in the Keil IDE?
I have been reading on the site and trough...
Normally with Segger Embedded Studio if you want to do a command-line build you use embuild.exe instead of emstudio.exe and away you go.
However, the NRF Connect/Zephyr...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
Hi,
We are using today SDK 15.0 and are upgrading to SDK 17.0 for development of our system.
In our application, we use BLE communication.
While comparing SDK_config...
