We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
I do my first project with nrf52.
I have great working app under the SES enviroment. App is downloaded to hardware under the Segger Studio and it works ok. And...
Greetings,
I am trying to create a bootloader project in VisualGDB (our IDE of choice) and GCC based off of the secure_bootloader/pca10056_s150_ble example. I was able to...
Hello,
we want to use RTC2 (RTC0 is used by SoftDevice, RTC1 by FreeRTOS) to keep track of time. I set NRFX_RTC2_ENABLED and NRFX_RTC_ENABLED in app_config.h. Code used...
I'm having an rather cryptic problem where around 0.01% bytes are simply not transmitted via UART for some reason. This error happens independently from the chosen baudrate...
Hi,
I have just started learning the ble mesh basics.I have started to build code using segger ide. I have to learn the mesh examples code in a detailed way for my upcoming...
Hi,
How do I configure Zephyr to turn off TWI and GPIO while in sleep mode? Once I enable those, idle power consumption doubles. I tried using device_pm_enable() on initialization...
Are there definitive specifications on the minimum pulse duration necessary to trigger GPIO DETECT events and PORT events? I have a sensor that fires a logic-low interrupt...
I would like space in flash that can be written to during production and then never changes or is overwritten. I have explored adding a section in the linker.
Are these...
Hi there...
I am using :
Device :Custom board using nrf52840 (fanstel module BT840)
SDK : nRF5_SDK_17.0.2
SoftDevice : S140 7.2.0
In order to add DFU capability...
Hello,
Any updates on the modem firmware v1.1.3 and v1.3.0 certification status for Verizon? I was told v1.1.3 was supposed to be around Q4 and v1.3.0 was supposed to...
The actual title is too long, the problem is this.
The documentation for s110 says:
Commands to write a buffer to flash
If the SoftDevice is enabled: This call initiates...
Hi All,
I am developing a Zigbee based light controlling product using nrf52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
All functionality and features developed...
Hi,
I run the radio test with our PCBA with SDK17.0.2, but when I want to send "start_tx_modulated_carrier 100", there's no callback response "<info> app: The modulated...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
