I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
Hello,
I'm currently trying to integrate the Android-nRF-Mesh-Library in our App.
Identifying works fine but when the library tries to send the public keys to the node...
We are developing a system were we rely heavily on the use of LWM2M. Using the provided LWM2M client we normally dont experience any problems at all and are able to establish...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
Hi,
In trying to take the PPI example code from nRF5_SDK_17.1.0_ddde560 and adapt it to use RTC for an event-end-point, I get the following error:
Error[Pe020]: identifier...
We have the Watchdog on the 5340 running but when we enter the software updater we wish to dissable it.
We have the following code to disable it but we are seeing the watchdog...
I have a private version of the VL53L1X driver ecause the driver in ncs2.9.0 hasnt been properly updated per my previous case. They suggested changing the CONFIG_VL53L1X=y...
Hi,
I am trying to get IQ data from nrf_dm_iq_tones_t and hopping sequence from nrf_dm_get_hopping_sequence with some clues from
I can see data but when I sort the data...
Hi,I have been using I2S communication in nrf54l15 DK board with zephyr but couldn't able to get clock to I2s .I couldn't able to get configure clock in overlay file ,can...
I get an error and the flashing fails when I attempt to flash the nRF52840 DK via an external J-Link Plus connected to the Debug In connector (P18).
Programming of the nRF52840...
I'm trying to sign the application for nrf9160, starting with different instructions I found, but none of them leads to success.
I followed the intructions:
Generate a...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Hello,
I have an application that I have been working on that was based off of the peripheral_uart example that I am using with the nRF52832. I was trying to see if I can...
Hi,
I would like to be able to hook into the system idle thread before/after the CPU is put to sleep to do some more custom power management things. Is there a way to...
