Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi,
I am working on the XIAO BLE SENSE board which has nRF52840 SOC with P25Q16h 2MB flash and other sensors
I want to access the external flash to store sensor data....
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
Hi, for nRF52840 raw proprietary RADIO mode, do TXADDRESS and RXADDRESSES imply a hard total node-count limit for a custom multi-node network, or only a simultaneous hardware...
SDK is NCS2.9.2,My device supports master-slave integration. As a slave, it can pair and bind with a mobile phone. As a master, it can scan and connect to two slave devices...
HI
I’m doing secondary development based on periodic_sync_conn in NCS 3.2.1 .
After establishing a periodic advertising sync, I have two issues:
Sometimes the buf...
Hello,
I'm trying to set up auto-provisioning and onboarding in my project as described in this sample: https://github.com/nrfconnect/sdk-nrf/blob/066ac6f61fe19ad91d805fd788d782e245f09a2e...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
On nRF5340 with external flash (SDK 3.2.x), is it possible to both support serial recovery enabled for both cores while supporting simultaneous DFU?
It seems like...
Hi,
i am developing under ncs 3.2.3 (then toolcahin 3.2.3 -> nrfutil-device 2.17.1).
FLashig OTP registers using batch method, i am getting the following "error" on nrf54l15dk...
Reference: first consult as Case id. 305571 Replyed by Tobjorn
I have a working proyect in wich 485 cable communication was replaced with NRF24L01+ but I need some help...
