Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I'm having trouble getting the Bluetooth Low Energy desktop library ( https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.1 ) set up on my Mac. My problem is occurring...
I would like to know what is the maximum ADC sampling frequency for transmitting data over Bluetooth to PC.
I am using two modules having an nRF52832 for each module....
Hello, I think there is an error in ble_advertising.c (SDK 15+).
Line 608, the code is trying to set the secondary phy but checks if the primary phy is valid ( ble_adv_primary_phy...
Hello,
I am very new to evaluating the nrf52-dk board, so I hope this is not too much of a trivial question.
I was trying to enable logging via UART without having to...
Hi
Currently I have a firmware based on template project for nrf52 (sdk15). I am interested in broadcast data, hence I used ble_advertising_advdata_update() in order to...
Hello! I use a 32kHz quartz resonator and I want to interrupt the program after 1 second with a watchdog timer. But when writing to it, 128 I get not 1 but 1.25 seconds. What...
Hello,
I followed the getting started guide but the kit can't connect. I'm getting this error:
net_if.net_if_init: There is no network interface to work with!
Is this...
Hi there,
I have a question NRF52840_PCA10056 and its SDK is latest nRF5 SDK.
The scenario is below:
The NRF52840_PCA10056 build a connection with a smartphone like...
1. It is understood that zigbee3.0 certification requires Green Power, but I did not see the definition and use of Green Power in the example. How does the nordic zigbee pass...
Hello Everyone,
I am trying to compile zigbee_light_coordinator example. I have my path included as ../../../../../../../external/nRF-IEEE-802.15.4-radio-driver/src in make...
Hello,
I have accidential removed the DFU bootloader on my PCA10059 dongel..... is there an image that I can write to the dongle to get it back into its out of the box condition...
Hi there, I have set my SAADC to have an acquisition time of 3us , however when I toggle a pin before and after calling
nrfx_saadc_sample_convert
I measure the time of...
The sample project is "nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\experimental\ble_nfc_pairing_reference"
I think "micro_ecc" is a normal build.
Please check attached...
Hi,
Using the Secure DFU from SDK 14.2 I managed to integrate the NUS peripheral example to have access to an UART pipe in parallel to the DFU when running the boot loader...
