Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
When using the PB-ADV bearer there is a ~10 second delay after the Link is closed and the mesh stack starts working again.
This is related to my previous report https:/...
I am trying to develop a SPI interface to a CANBUS controller for the nRF9160 for the zephyr platform.
The issue I am having at this point is is that I am unable to see...
Hello,
I am working on a custom pcb with nrf9160-SICA. I have UART SPI and GPIOs running fine but I am having a very difficult time with I2c (TWI).
Pins 8 and 9 are occupied...
Hello,
I'm trying to use the nrf52840 Dongle on the Raspberry 3B+. I didn't achieve to run an appImage downloaded from your site. When i'm executing the app nothing happens...
My current hardware is based on SoftDevice SD132, v6.0.0 as provided with SDK 15.0.0. I would like to update it to use SoftDevice 6.1.0 (as part of SDK 15.2.0) and perhaps...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5 under Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for...
we have designed a board using Nrf9160 IC and we have issue with SIM module. we not getting 1.8 volt in "SIM_1V8" pin. when running mqtt sample program we are getting
...
Hi,
Using nRF52840 with SDK15.0.0.
I started my projetc based on BLE tutorial characteristics.
I created my service and add 2 characteristics successfully.
My module...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
