We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi!
I try to write SD to 52810 and nrg go studio can't do it. After recover it can't to switch normal window with possibility erase device and SD write. What possible reason...
SDK 14.2 / SD132 5.0 / NRF52832 --> NRF52832
There is a thread here which discusses "when NUS is ready" : https://devzone.nordicsemi.com/f/nordic-q-a/28208/when-is-nus-ready...
I'm using SDK nRF5_SDK_15.0.0_a53641a, and I was able to trigger the hard fault handler from within the Nordic NFC library. Nothing was running. The microcontroller was asleep...
Hi
Some time ago, we purchased a couple of boards, then (I believe) called nRF52 PDK. They are marked PCA10056.
We need to obtain more nodes. From gleaning information...
Hello there,
I'm looking for a good source that explains the ideology of the Nordic methods for programming and debbuging the nrf5 chips so I'm looking for something that...
Hi,
I'am trying to run the example in Software Development Kit > nRF5 SDK > nRF5 SDK v14.2.0 > Examples > Bluetooth low energy examples > Experimental: IoT Examples > TCP...
Hi,
We have our nrf52840 module going to be ready soon. For production testing, what is the recommended and capable lower tester and upper tester? I am sure that nrf51822...
Hi all I am wrking in an sample be program where ble is advertising everey 5 seconds. I have configured app timer with fire period = 5 seconds in order to read a sensor. After...
Hi,
Ipv6 UUID 0x1820 shall be present in the advertising process. Is it mandatory to put it in the ADV_IND message or can it be in the SCAN_RSP one ? ... the scanner, 6BR...
Currently, we are testing Bonding & Connect.
Please see the attached log below.
If Click 「Bond」 on Android App (nRF Connect), disconnection occurs after "PM_EVT_CONN_SEC_SUCCEEDED...
Hello,
I have the following question: when developing a software product, I developed my own service. It consists of one characteristic and several descriptors (valid range...
On our products, we assign a custom sequential mac address to each unit (we use this number in other places in our system). I believe this is an issue due to the bootloader...
Hello all,
We are using nRf52832 DK.
We are trying to run TCP Client example from IOT.we have even burned the s1xx_iot soft device.We are getting the the error "CMSIS...
Hi,everyone!
I need to configure an external interrupt so that when the interrupt is triggered, I can do something else
When I configure it in the following code...
Hi
Hi i am trying my application for sleep and wakeup without gpio. Actually my work is to put my device(battery powered) in sleep for 5 minutes and after that it should...
