Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,
I try to develop a Bluetooth speaker using the nRF 5340 DK since i do not have a separate audio Dk for this. I am using the sample code Audio unicast client for this...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
When I get a custom board, how do I detect and flash it? I have three options on the board:
I have a USB cable with:
GND
D+
D-
+5V
OR can configure the usb...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
Our device is set up to provide AT Commands directly to nRF9160 using a USB UART connection and control using a VT100 Terminal simulator. When attempting to connect to the...
Hello. I'm using npm1300ic. In one example, there is a battery_model.inc file related to li-po 3.7v 200 mah battery, and the battery you are currently using is li-ion 3.7v...
When dynamically allocating BLE GATT services and characteristics using custom structures and Zephyr’s dynamic memory functions (e.g., k_malloc, k_calloc), the service registration...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hello Nordic team, Whilst porting our product from nRF Connect 2.4.1 to 2.9.1 we encountered the following problem. When compiling with ZIGBEE_FACTORY_RESET=n we get Seems...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
i'm looking for an extremely simple BLE beacon app, which advertises (say) at 1HZ and then enters a "low-power" sleep mode....
there are numerous samples included in the...
Hello forum ,
In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
