Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I have tried to create delay_timer function using app_uart as nrf_delay replacement in order to save power as much as possible in a short delay existed in any part of my code...
I tried all the examples TWI code on my device and a dev kit nRF51-DK. Nothing appeared to work, either I get a into the WDT handler or the nRF51 resets.
While combing...
Hello,
My name is Mehdi, and I am a student in a french university. Actually, I am working on a project and I aim to use the Heart Rate for a statical studies to use it...
Hi,
I'm trying to use the NRF24L01 as a replacement to HS6200p. But I can't find 0x1E (SETUP VALUE) and 0x1F (PRE_GURD) in the NRF24L01 datasheet. Actually, in the datasheet...
Hi everyone,
I am using the following:
*nRF51422
*SDK11
*keil uVision 5.17
*s130
I have been working with nRF51 that scans beacons and stores it into persistent...
Hello everyone,
I am trying to set the security parameters for bonding with PASSKEY (static)format it is getting executed very well(connected and bonded) for the SDK 9...
Dear all:
My device uses LDO mode and DC-DC mode respectively, and the distance is different.In 4dbm, the distance of the LDO mode is 110m, while the LDO mode is in the 70m...
Hi,
I was wondering if anyone could clarify why there are enable, set and clear (CHEN, CHENSET, CHENCLR) for the PPI channels when according to the data sheet they all...
I checked S130 document for using nRF51822.
I want to change the nRF51822 like the following mode.
peripheral => central => scanning => peripheral => central => scanning...
Hello
I am trying to change the ticks value of Battery measurement interval (ble_app-prox example) but i am not able to understand how the ticks period is measured based...
Hi,
I was seeing memory leak issues when using NRF51 with JLkink v4.98. See this link:
forum.segger.com/index.php
This issue has been fixed with the latest version of...
The address miss event is not shown as a transition in Figure 22 of the NRF51 Reference Manual. What state does the NRF51 enter upon an address miss and how long after the...
To use BEL application, the soft device must be downloaded before programming.
i can find a table shows that which soft device version is suitable for chip version.
how...
Our application is developing RC units for small (indoor) model airplanes - we want to be able to have multiple planes flying at once without "stepping" on each other.
...
