Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hello!
I have question about Direction Finding in nRF52811, Angle-of-arrival to be exact.
To begin with, I have a custom board with nrf52811 onboard and 8 antennas....
Hi
As far as I know, NFC supports peer-to-peer communication, so I want to know whether peer-to-peer communication can be achieved between two 52832 through NFC? Is there...
Hello everyone.
Iam working on a project where i need to detect a falling edge from a ADC (ADS1298) when new data is ready at a sample rate of 500SPS. I have the issue...
Hi Great Nordic Support Teams:
I'd like to know schedule of nrf9160 specification:
1.When will 9160 support R14 regulation in NB-IOT/ LTE ?
2.When will Nordic release...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I ported UART into my code and it...
Hey all,
I would like to make a flexible design with ability to assemble NRF52832 or NRF52810 , both are pin to pin compatible ,
But i just wonder how to consider regulation...
Hello,
I am developing a capacitive sensing application with the nRF52 DK and Segger Embedded Studio. So far I have integrated the Capacitive Sensor Library Example into...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
